[SATLUG] SMART error (CurrentPendingSector) detected on host
Sean Carolan
scarolan at gmail.com
Thu Sep 20 14:08:30 CDT 2007
> What is the output of smartctl -a /dev/xxx ?
Since you asked for it (serial numbers removed by me):
=== START OF INFORMATION SECTION ===
Device Model: Hitachi
Serial Number:
Firmware Version:
User Capacity: 82,348,277,760 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 1
Local Time is: Thu Sep 20 14:05:10 2007 CDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (1445) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 24) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 097 097 016 Pre-fail
Always - 262147
2 Throughput_Performance 0x0005 100 100 050 Pre-fail
Offline - 0
3 Spin_Up_Time 0x0007 121 121 024 Pre-fail
Always - 165 (Average 165)
4 Start_Stop_Count 0x0012 100 100 000 Old_age
Always - 172
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail
Always - 0
8 Seek_Time_Performance 0x0005 100 100 020 Pre-fail
Offline - 0
9 Power_On_Hours 0x0012 100 100 000 Old_age
Always - 1285
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age
Always - 153
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age
Always - 226
193 Load_Cycle_Count 0x0012 100 100 000 Old_age
Always - 226
194 Temperature_Celsius 0x0002 139 139 000 Old_age
Always - 43 (Lifetime Min/Max 24/52)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age
Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age
Always - 1
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age
Always - 0
SMART Error Log Version: 1
ATA Error Count: 41 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 41 occurred at disk power-on lifetime: 1277 hours (53 days + 5 hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 97 47 0b f1 Error: UNC 2 sectors at LBA = 0x010b4797 = 17516439
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 02 97 47 0b f1 00 00:41:28.900 READ DMA
c8 00 08 cf 7d 00 f0 00 00:41:28.900 READ DMA
ca 00 08 cf 7d 00 f0 00 00:41:28.900 WRITE DMA
c8 00 08 cf 7d 00 f0 00 00:41:28.900 READ DMA
40 00 08 cf 7d 00 f0 00 00:41:28.900 READ VERIFY SECTOR(S)
Error 40 occurred at disk power-on lifetime: 1277 hours (53 days + 5 hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 97 47 0b f1 Error: UNC 8 sectors at LBA = 0x010b4797 = 17516439
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 97 47 0b f1 00 00:41:23.900 READ DMA
c8 00 01 00 00 00 f0 00 00:41:23.900 READ DMA
c8 00 08 97 47 0b f1 00 00:41:19.100 READ DMA
c8 00 01 00 00 00 f0 00 00:41:19.100 READ DMA
c8 00 08 97 47 0b f1 00 00:41:14.300 READ DMA
Error 39 occurred at disk power-on lifetime: 1277 hours (53 days + 5 hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 97 47 0b f1 Error: UNC 8 sectors at LBA = 0x010b4797 = 17516439
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 97 47 0b f1 00 00:41:19.100 READ DMA
c8 00 01 00 00 00 f0 00 00:41:19.100 READ DMA
c8 00 08 97 47 0b f1 00 00:41:14.300 READ DMA
c8 00 08 97 47 0b f1 00 00:41:09.500 READ DMA
c8 00 08 8f 47 0b f1 00 00:41:09.500 READ DMA
Error 38 occurred at disk power-on lifetime: 1277 hours (53 days + 5 hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 97 47 0b f1 Error: UNC 8 sectors at LBA = 0x010b4797 = 17516439
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 97 47 0b f1 00 00:41:14.300 READ DMA
c8 00 08 97 47 0b f1 00 00:41:09.500 READ DMA
c8 00 08 8f 47 0b f1 00 00:41:09.500 READ DMA
c8 00 08 87 47 0b f1 00 00:41:09.500 READ DMA
c8 00 08 7f 47 0b f1 00 00:41:09.500 READ DMA
Error 37 occurred at disk power-on lifetime: 1277 hours (53 days + 5 hours)
When the command that caused the error occurred, the device was
active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 97 47 0b f1 Error: UNC 8 sectors at LBA = 0x010b4797 = 17516439
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 97 47 0b f1 00 00:41:09.500 READ DMA
c8 00 08 8f 47 0b f1 00 00:41:09.500 READ DMA
c8 00 08 87 47 0b f1 00 00:41:09.500 READ DMA
c8 00 08 7f 47 0b f1 00 00:41:09.500 READ DMA
c8 00 08 77 47 0b f1 00 00:41:09.500 READ DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining
LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1283 -
# 2 Short offline Completed without error 00% 1281 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
More information about the SATLUG
mailing list