[SATLUG] New camera prob

hc at lookcee.com hc at lookcee.com
Sat Jan 15 22:17:10 CST 2011


Thanks Mark but Kodak does not support linux with it's install software so this should work tru simply connecting the cam and having the USB drivers set it up as a file system .. That is my understanding anyway. Also consider that 'shotwell does see the cam and finds it locked... locked by whom is my question but I do not know how to ask. I ran 'hwinfo' and  ( I cannot understand it perhaps someone can) here are the failure lines I think:

[   57.240815] Bluetooth: RFCOMM socket layer initialized
[   57.240819] Bluetooth: RFCOMM ver 1.11
[  115.920260] usb 1-4.3: new full speed USB device using ehci_hcd and address 4
[  116.053747] usb 1-4.3: configuration #1 chosen from 1 choice
[  174.024131] usb 1-4.3: usbfs: USBDEVFS_CONTROL failed cmd shotwell rqt 128 rq 6 len 255 ret -110
[  175.024189] usb 1-4.3: usbfs: USBDEVFS_CONTROL failed cmd shotwell rqt 128 rq 6 len 1000 ret -110
[  176.024246] usb 1-4.3: usbfs: USBDEVFS_CONTROL failed cmd shotwell rqt 128 rq 6 len 255 ret -110
[  177.024181] usb 1-4.3: usbfs: USBDEVFS_CONTROL failed cmd shotwell rqt 128 rq 6 len 1000 ret -110
[  204.000627] usb 1-4.3: USB disconnect, address 4
[  250.772385] usb 1-4.3: new full speed USB device using ehci_hcd and address 5
[  250.898737] usb 1-4.3: configuration #1 chosen from 1 choice
[ 3037.428439] usb 1-4.3: USB disconnect, address 5
[ 3739.876328] usb 1-4.3: new full speed USB device using ehci_hcd and address 6
[ 3740.002023] usb 1-4.3: configuration #1 chosen from 1 choice
[ 3745.053997] usb 1-4.3: USB disconnect, address 6
[ 3777.256292] usb 1-4.3: new full speed USB device using ehci_hcd and address 7
[ 3777.385563] usb 1-4.3: configuration #1 chosen from 1 choice
[ 3787.392142] usb 1-4.3: usbfs: USBDEVFS_CONTROL failed cmd f-spot rqt 128 rq 6 len 255 ret -110
[ 3788.392198] usb 1-4.3: usbfs: USBDEVFS_CONTROL failed cmd f-spot rqt 128 rq 6 len 1000 ret -110
[ 3789.392133] usb 1-4.3: usbfs: USBDEVFS_CONTROL failed cmd f-spot rqt 128 rq 6 len 255 ret -110
[ 3790.392232] usb 1-4.3: usbfs: USBDEVFS_CONTROL failed cmd f-spot rqt 128 rq 6 len 1000 ret -110
[ 3803.312078] usb 1-4.3: usbfs: USBDEVFS_CONTROL failed cmd f-spot rqt 128 rq 6 len 255 ret -110
[ 3804.312260] usb 1-4.3: usbfs: USBDEVFS_CONTROL failed cmd f-spot rqt 128 rq 6 len 1000 ret -110
[ 3805.312196] usb 1-4.3: usbfs: USBDEVFS_CONTROL failed cmd f-spot rqt 128 rq 6 len 255 ret -110
[ 3806.312130] usb 1-4.3: usbfs: USBDEVFS_CONTROL failed cmd f-spot rqt 128 rq 6 len 1000 ret -110
[ 3855.792294] usb 1-4.3: usbfs: USBDEVFS_CONTROL failed cmd shotwell rqt 128 rq 6 len 255 ret -110
[ 3856.792227] usb 1-4.3: usbfs: USBDEVFS_CONTROL failed cmd shotwell rqt 128 rq 6 len 1000 ret -110
[ 3857.792163] usb 1-4.3: usbfs: USBDEVFS_CONTROL failed cmd shotwell rqt 128 rq 6 len 255 ret -110
[ 3858.792242] usb 1-4.3: usbfs: USBDEVFS_CONTROL failed cmd shotwell rqt 128 rq 6 len 1000 ret -110
[ 5016.681172] usb 1-4.3: USB disconnect, address 7
herb at herb-Aelf:~$ 


-----Original Message-----
From: "mark" <mark at kandm-solutions.com>
Sent: Saturday, January 15, 2011 21:02
To: "The San Antonio Linux User's Group Mailing List" <satlug at satlug.org>
Subject: Re: [SATLUG] New camera prob

I know that some of these type of devices require that you tell tell it
to connect to the PC. I had a phone that I had to go into the settings
for. I had to tell it that it was a pc connection and that it should act
like a mass storage device. 



On Sat, 2011-01-15 at 18:58 -0600, hc at lookcee.com wrote:
> Hi all, I run Ubuntu-10.04 plenty mem and P-IV-3.2 my cam died and just replaced wi Kodak C-182. Gnome does not see it auto so I tried F-spot nj, then after googling I found several clients to try but nj on any and most recommended was 'Shotwell'.  ('shotwell' say "The camera is locked by another application.  'Shotwell' can only access the camera when it's unlocked.  Please close any other application using the camera and try again".) I have found a lot of pages on this prob. but I cannot really understand how to find out what has taken over the camera when it is tethered, dunno what to do. 
> 
> My next move is to un-install all of the camera type progs then install 'shotwell' alone if Gnome does not see it on boot. My head tells me that surely there are commands I could use to unlock the cam or to at least find out 'who' has grabbed it. However, ignorance blocks that path.
> 
> Any suggestions to try before I start down the de-installing?
> Thanks herb
> 

-- 
_______________________________________________
SATLUG mailing list
SATLUG at satlug.org
http://alamo.satlug.org/mailman/listinfo/satlug to manage/unsubscribe
Powered by Rackspace (www.rackspace.com)




More information about the SATLUG mailing list